2 | n-doy
Agustus 12, 2008 pada 4:49 pm

tlg ksh solusi tntang service error
terima kasih

4 | Arjack
November 5, 2008 pada 10:37 am

thank’s berat buat solusi na!
I coba dulu y
truz kalo’ buat error 5010 buat mp160 gmn solusinya boz???
pliz y!!
thanks lg!

6 | arjack
Januari 12, 2009 pada 11:24 am

w udah coba berkali2 bro tp ga berhasil juga!!! (w nya yg goblok kale yah ^^)
tapi setelah w jalan2 ama uncle google w dapet banyak info.
check it out :
LED DISPLAY ERROR (ERROR CODE) PARTS LIKELY TO BE FAULTY
E 2 2 Carriage Error (5100) - Carriage unit (main unit)
- Timing slit strip film
- Logic board ass’y
- Carriage motor (main unit)
E 2 3 Paper Feed Error (6000) - Timing sensor ass’y
- Timing slit disk film (main unit)
- Feed roller ass’y (main unit)
- Logic board ass’y
- Paper feed motor (main unit)
E 2 4 Purge cam sensor error (5C00) - Carriage unit (main unit)
- Timing slit strip film
- Logic board ass’y
- Carriage motor (main unit)
E 2 5 ASF Cam sensor error (5700) - Drive ass’y (main unit)
- PE Sensor ass’y
- Pressure roller ass’y (main unit)
E 2 6 Internal temperature rise error (5400) - Logic Board Ass’y
E 2 7 Main ink absorber full (5B00)
Or
Platen ink absorber full (5B10) - Main ink absorber:
Bottom case unit (main unit)
Ink absorber kit
- Platen ink absorber:
Ink absorber
Ink absorber kit
E 2 8 Ink cartridge temperature rise error (5200) - Print head
E 2 9 EEPROM error (6800) - Logic board ass’y
E 3 2 AP position error (6A00) - Driver ass’y (main unit)
- PE sensor ass’y
- Logic board ass’y
E 3 5 USB Host VBUS over current (9000) - Logic board ass’y
E 3 7 Abnormal motor driver error (9000) - Logic board ass’y
E 4 0 Other hardware error (6500) - Logic board ass’y
E 4 2 Scanner error (5010) - Scanner unit
- Logic board assy

ini gue kasi tau kode-kode error buat mp 150 & 160
MP150/MP160 ERROR CODE
E9 The connected digital camera / video camera does not support Camera
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 – Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error – USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error
E42 22 Scanner error
How to clear E27 Code
* With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
* When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
* When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
* When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in orange and green, starting with orange.)note: press 4 times for waste ink counter reset.
The number of the Reset button pressing LED Function Remarks
0 time Green Power off
1 time Orange Service pattern print (auto teste)
2 times Green EEPROM print (dados da EEPROM)
3 times Orange EEPROM reset (EEPROM reset)
4 times Green Waste ink counter reset (Absorvente reset)
* Turn off the printer.( it must be turn off) then turn it on again.
tp reset error 4,2 gue gk tau bantuin dong…or email gue (cims_pm@yahoo.com) thx atas bantuannya

Pernah ngalamin hal seperti ini udah kelar isi tinta printer trus gak bisa print kata komputernya sih.. cartridgenya error na.. kalo buat fixednya mudah kok cuma jalanin step-step ini kelar deh.. problemnya udah aku coba dan berhasil. Stepnya sebagai berikut :Step 1 Push Power switch by continue (Tekan Power On/Off)
Step 2 inserrt plug(Masukan Power, Power Tetap di Tekan)
step 3 Tekakan Tombol Reset 1x, lepaskan Tombol Pwr, Tekan Reset sekali lagi Sampai Menjadi “0?
Step 4 Push + display change from “0? to “1?(tekan tmbl + Untk merubh ‘0′ ke ‘1′)
Step 5 Push Power switch again , Printer will be print 1 page(tekan tmbl pwr –> tmbl start sampai ngeprint 1 hal.)
step 6 Open cover(buka tutup printer)
Step 7 unplug(cabut kabel power)
Step 8 Take out ink 40 and 41(lepaskan catridge 40 dan 41)
Step 9 Insert plug again(pasang kabel power)
Step 10 Push power switch(tekan tmbl power)
Step 11 Open cover (scan cover)(buka tutup scaner)
Step 12 Inksert ink 40 , 41 again(masukan catridge 40 dan 41)
Printer will be not alaram low ink and not shown error code “E5?
Selamat mencoba ya mudah-mudah berhasil … sourcenya juga copy-paste ketemu dari search engine (om google)
Canon Printer Error Code 5100

Summary:
Generally, error code 5100 is error code of blinking error in orange/green 2 times. Both these symptom due to the same problem: carriage error (also known as CR error. CR= Carriage Return).
Please check out the previous post for more details about this problem.

Tambahan Dikit :
Error Code………Description
5000 ……………….Home position error
5100 ……………….Carriage control error
5200 ……………….Head temperature sensor error
5400 ……………….Printer temperature sensor error
5600 ……………….No cartridge error
5C00 ……………….Purging operation error
5200 ……………….Scanner cartridge error

As a technician, I have worked on tons of printers. This particular error had stumped me for a while, but I finally found the cause. As others had pointed out before, it can have alot to do with some obstruction in the print path, the gears, or ink on the clear plastic encoder strip. You’re on the right track – I found the the purge cap (the white sliding mechanism that the print head parks to when it’s not in use) was not lubricated well enough from factory. If you lubricate the sliders with some white grease (don’t get it on the small wipers or the black caps) the mechanism can now slide more freely, and the unit can park the head properly without giving you the dreaded head homing error 5100 (or E-2-2 on the LCD display) Keep in mind that this repair will probably require you to remove the right panel off of the printer to gain access to the purge mechanism. There are two screws behind the printer, and two in front for each corrosponding side panel (the front screws are behind the grey front panel of the printer – open the top cover to see the clips which hold the front cover on) Hope this helps some of you out.

mudah2an bisa bermanfaat ^^